PowerSmart DBSM24E PSS2240 User Manual

The PowerSmart DBSM24E PSS2240 user manual will help you know how to operate the machine and know the important features in one simple, easy-to-understand document.

You are lucky to have purchased this PowerSmart DBSM24E PSS2240 snow thrower. With a nice and stylish design. Also has good quality. This is the right tool for clearing snow that has accumulated around your house.

As the owner of a snow blower machine you must have the knowledge to be able to operate the machine properly. We will help you gain that knowledge. This time you can get the pdf of the PowerSmart DBSM24E PSS2240 user manual here. The following is a snippet of the pdf document which you can later find at the end of the page.

This is the table of contents which will be found in the full user guide pdf.

• Technical data
• Introduction
• Safety information
• Knowing your snow thrower
• Assembly and adjustments
• Snow thrower preparation
• Operating your snow thrower
• Maintenance
• Storage & Cleaning
• Troubleshooting
• Exploded view and parts list
• Two (2) years limited warranty

Operating Your Snow Thrower Manual Start The Engine 

To manual start the engine, perform the following steps:

1. Check the oil and fuel levels.
2. Turn the fuel valve to the “ON” position.
3. Move the choke lever to the “CLOSE” position.
4. Make sure to insert the switch key.
5. Press the primer bulb 3 times.
6. Pull on the recoil starter handle slowly until a slight resistance is felt, then pull quickly to start the engine. Return cord gently into the recoil starter. Never allow the cord to snap back.
7.  If the engine fails to start, repeat step 6. NOTE: After repeated failed attempts to start the engine, please consult the troubleshooting guide before attempting again. If problems persist, please call customer service.
8. Once the engine has started, slowly return the choke lever all the way to the “OPEN” position.
9.  Allow the engine to run for several minutes before cleaning snow. This allows the engine to stabilize its speed and temperature. 

Electric Start The Engine

To start the engine using the electric start function, perform the following steps:

1. Check the oil and gas levels.
2. Turn the fuel valve to the “ON” position.
3. Move the choke lever to the “CLOSE” position.
4. Make sure to insert the switch key.
5. Press the primer bulb 3 times.
6. Plug the power cord to the starting motor.
7. Press the start button for 2-3 seconds or until the engine starts. NOTE: If the engine does not start after 2-3 seconds, release the start button.
8.  If engine fails to start, wait 10 seconds, then repeat step 7. NOTE: After repeated attempts to start the engine, please consult the troubleshooting guide before attempting again. If problems persist please call customer service.
9.  Once the engine has started. Slowly move the choke lever all the way to the “OPEN” position. Allow the engine to run for several minutes before attempting to clean snow.

CLEARING SNOW

Start the engine once your snow thrower has been running outside for several minutes, it is now ready for use. Make sure the path in front of your Snow Thrower is free from people, animals, objects, and all other obstructions except for snow. 

Adjust the chute outlet to the desired direction. Turn the chute rotation handle clockwise or counter-clockwise until the desired position is reached. 

WARNING! Never direct the chute outlet toward people or animals. While snow may seem harmless, it can contain rocks or other debris that can cause serious injury when projected through the chute.

1. Engage/depress the auger control lever (handle) to start the augers and impeller turning.
2. Set the desired direction and speed using the speed/gear control lever. 18
3. Engage/depress the drive control lever (handle) and direct the snow thrower into the snow to be cleared.

It is a small snippet of the contents of the pdf user guide. In the pdf version you will get a more complete guide such as how to prepare the machine early, how to maintain the machine, and troubleshooting if an error occurs. All are discussed in full in the pdf user guide. Please download from the button we have provided below.